[Solved] Seagate 6tb drive not displaying temp in Dynamix but does in UnMenu

I ran 3 preclear cycles with the Seagate 6tb attached to the Motherboard and it displays the temp as "0)". Had 2 WD 4TB Reds preclearing also, and they did display a temp. I now have it hooked it up to my new sata controller, and it does not display a temp. There are no jumpers attached to it. Suggestions for my next step?

Drive - Seagate Desktop HDD 6TB 6Gb/s 128MB Cache 3.5-Inch Internal Drive Retail Kit (STBD6000100) (http://www.amazon.com/Seagate-Desktop-3-5-Inch-Internal-STBD6000100/dp/B00JBJ34WC/ref=sr_1_1?ie=UTF8&qid=1414374227&sr=8-1&keywords=Seagate+Desktop+HDD+6TB+6Gb%2Fs+128MB+Cache+3.5-Inch+Internal+Drive+Retail+Kit+%28STBD6000100%29)

New Sata Controller - SUPERMICRO AOC-SAS2LP-MV8 PCI-Express 2.0 x8 SATA / SAS 8-Port Controller Card (http://www.newegg.com/Product/Product.aspx?Item=N82E16816101792)

Info about the drive:

/dev/sdc:

ATA device, with non-removable media
        Model Number:       ST6000DX000-1H217Z
        Serial Number:      Z4D06290
        Firmware Revision:  CC47
        Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SAT                  A Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
        Used: unknown (minor revision code 0x001f)
        Supported: 10 9 8 7 6 5
        Likely used: 10
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:11721045168
        Logical  Sector size:                   512 bytes
        Physical Sector size:                  4096 bytes
        Logical Sector-0 offset:                  0 bytes
        device size with M = 1024*1024:     5723166 MBytes
        device size with M = 1000*1000:     6001175 MBytes (6001 GB)
        cache/buffer size  = unknown
        Form Factor: 3.5 inch
        Nominal Media Rotation Rate: 7200
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = ?
        Advanced power management level: 128
        Recommended acoustic management value: 208, current value: 208
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    SMART feature set
                Security Mode feature set
           *    Power Management feature set
           *    Write cache
           *    Look-ahead
           *    WRITE_BUFFER command
           *    READ_BUFFER command
           *    DOWNLOAD_MICROCODE
           *    Advanced Power Management feature set
                Power-Up In Standby feature set
           *    SET_FEATURES required to spinup after power up
                SET_MAX security extension
           *    48-bit Address feature set
           *    Mandatory FLUSH_CACHE
           *    FLUSH_CACHE_EXT
           *    SMART error logging
           *    SMART self-test
           *    General Purpose Logging feature set
           *    WRITE_{DMA|MULTIPLE}_FUA_EXT
           *    64-bit World wide name
           *    IDLE_IMMEDIATE with UNLOAD
                Write-Read-Verify feature set
           *    WRITE_UNCORRECTABLE_EXT command
           *    {READ,WRITE}_DMA_EXT_GPL commands
           *    Segmented DOWNLOAD_MICROCODE
                unknown 119[6]
                unknown 119[8]
           *    Gen1 signaling speed (1.5Gb/s)
           *    Gen2 signaling speed (3.0Gb/s)
           *    Gen3 signaling speed (6.0Gb/s)
           *    Native Command Queueing (NCQ)
           *    Phy event counters
           *    Idle-Unload when NCQ is active
           *    unknown 76[15]
                DMA Setup Auto-Activate optimization
                Device-initiated interface power management
           *    Software settings preservation
                unknown 78[7]
           *    SMART Command Transport (SCT) feature set
           *    SCT Write Same (AC2)
                unknown 206[7]
                unknown 206[12] (vendor specific)
           *    reserved 69[3]
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
                supported: enhanced erase
Logical Unit WWN Device Identifier: 5000c500676a28df
        NAA             : 5
        IEEE OUI        : 000c50
        Unique ID       : 0676a28df
Checksum: correct

Edit: Added SS of drive

So an update. I opened up UnMenu and the temp is displaying. I guess this is a problem with the Dynamix GUI. I will post in the plugin thread now.

Edit***

I had this issue with 2 6tb disks. HGST & Seagate. I added the HGST to the array, and it started displaying the temp correctly. Parity has been built and is being checked. Everything looks good now.