arcane

Installed MotionEye and was able to set up the camera and view RTSP stream. However, while it seems to be recording, I cannot play the video in the browser or after downloading it. It states that it is "unsupported media" even after changing various codecs. Any suggestions? Thank you.

Installed MotionEye and was able to set up the camera and view RTSP stream. However, while it seems to be recording, I cannot play the video in the browser or after downloading it. It states that it is "unsupported media" even after changing various codecs. Any suggestions? Thank you.

Thanks all for chiming in. I have the system in safe mode right now with no plugins or Dockers running. Hopefully it will stay stable for at least a week without crashing. Enclosed are the diagnostics. ThomasE - I don't know if FCP is causing the crashes. I think I had FCP installed for a while in previous versions and the system was stable. It was only when I upgraded unRAID a few versions (don't recall which) ago that the crashes started happening. This is when I tried to run Troubleshooting mode in FCP to catch the error. Oddly enough, it never crashed while Troubleshooting mode was on. But when I rebooted the system to stop Troubleshooting mode, the system again crashed intermittently. tower-diagnostics-20191121-0729.zip

No... just without plugins and I am not using VMs. So basically just re-enable dockers one at a time? It's just perplexing why the system was stable until the recent versions, and whatever FCP Troubleshooting did, it restored the stability. No way to go back to an earlier version since it's deprecated?

Just an update. I ran memtest for four days, without any errors. However, running it in safe mode still does not eliminate the random crashes every few days. I don't see anything in the log from when it runs normally up until the time it crashes. I'm at a loss as to what to do now to eliminate the crashes. Again, not sure why, but when Troubleshooting mode was run in the old FCP, it ran for months without issue. Any suggestions appreciated. Thank you.

Still getting the XDG error with the latest pull. Any options to get it working? Thank you.

Hi John. The segfault does not consistently appear. Also, if it was bad RAM or software incompatibility, wouldn’t it also crash with the Troubleshooting mode in FCP when it was running? It never crashed, for whatever reason, as long as that was going so I’m not sure what was different. Regardless, I’ll try a memtest to narrow things down.

For several versions now, I have been getting random crashes that happen intermittently without apparent cause. Sometimes it lasts a day before crashing, sometimes several. Ironically, when I used the Fix Common Problems plugin's troubleshooting mode to capture logs where it may happen, it never crashed. When I turned off Troubleshooting mode, it eventually crashed. Now that I've updated to 6.7.2, there no longer is a Troubleshooting mode in FCP and it mentions to use the syslog server instead. I've done that, but the logs show nothing unusual and the system still crashes randomly. Enclosed are some logs where you can see where it crashed after a day, and another where it went a few days. Any inout appreciated. Thank you. syslog-192.168.11.110.log

Unfortunately, I'm still getting the "ERROR: openbox-xdg-autostart requires PyXDG to be installed" and having it time out. I have tried setting it to no user and pass, user with no pass in an MD5 hash, default abc and abc password as hash, empty in both setup variables, no luck. Any suggestions? Thank you.

I just tried to install this Docker and everything downloaded fine but would not install. The error is: Error: failed to register layer: ApplyLayer exit status 1 stdout: stderr: write /usr/share/file/magic.mgc: no space left on device Couldn't find any reference to it so would appreciate some guidance. Both my flash and cache drives are over 98% free.

Thank you Frank. No wonder I missed it as it was in another place entirely!

@dlandon I've just installed this plugin to disable Telnet but noticed that there is not an option for that. Has it been removed?

Just installed the plugin today and didn't notice that there was a toggle for disabling telnet, only FTP. Am I missing something?

Hello, Having an issue with Privoxy, as I just realized that connections are not routed through it. Though, if I connect manually to the VPN to verify credentials, it works. I had it set up with a custom OpenVPN and it seems to connect fine according to the log. I can also download torrents but not sure if it is going through the VPN. How do I verify if deluge is actually using the VPN? And any suggestions to resolve problems with Privoxy?

Hmmm... that's what I thought but not sure how to update it. I don't think there's a crt specified in the ovpn file. I'm running my own VPN on AWS through streisand. If you have any suggestions, I'd appreciate it. Thanks!