angerthosenear

Sadly no, I'm still on 6.8.3. I haven't tried much past that day to troubleshoot the issue due to it being used in our office.

After upgrading from 6.8.3 to 6.9.1 the server hangs after Loading /bzimage... ok Loading /bzroot...ok I've also tried GUI Mode and it hangs after loading bzroot-gui. I tried the update through the interface from 6.8.3, and manually replacing the bz* files from a manual download and copying to the flash directly I ended up having to revert to 6.8.3 which booted without issue. Attached is the diagnostics from 6.8.3. zdserver-diagnostics-20210316-0859.zip

Status update! Array successfully rebuilt and running 100%! Thanks again!

Update: Controller reappeared after a reboot. Emulated data looks good. In progress of a rebuild at the moment. Thanks for your help!

Awesome, thanks for your help! Will update how it goes tonight.

If the drives do appear after a reboot, I'm guessing I should just generally check for any actual SMART errors if it can see them and replace drives as necessary. Otherwise a rebuild/sync should be fairly worry free?

This would be a full data rebuild on these two drives then correct? Will there be anything special to do on boot or will it be fairly automatic when it powers back on to do a parity check? Would I have to re-assign these drives to their slot or is there a better approach?

It's not an add-on card. It's built into the mobo. I don't mind rebooting to see if it comes alive, but I know not to do so in favor of getting any logs. EDIT: Further checking the mobo manual. The Asmedia controller is truly just for two SATA ports.

Unraid version: 6.7.0-rc7 Two parity disks. Got an alert this morning that two of my drives entered an error state. This occurred during a parity check which it appears to have auto-paused once these disks were disabled. From the Dashboard those disks show a healthy SMART data report, but alas I cannot actually get any SMART data from those disks. I get the below response for them: smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.33-Unraid] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org Short INQUIRY response, skip product id A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. At the moment I'm holding off touching anything just to be safe. Would like some insight on how to approach resolving this. It's a bit concerning since I'm down two disks now. Attached diagnostics info. Thank you for your help! undine-diagnostics-20190429-1330.zip

I tried enabling that, but it didn't seem to find the mineos (Node version). Not sure if I have to do a full reload after enabling that or not. Maybe that's why it didn't find it.

Yeah I found that out, I was unsure what went where when making the template. It's now downloading the required files and seems to be working well. Thanks for the help!

The one already there uses a slightly different version of MineOS and uses Java 7, so some things start to behave weirdly. I did try it though!

Right. But, I couldn't find out how to go from that to a running docker container since there is no template (that I'm aware of). EDIT: Or do I make the template with Add Container, and point the repo to that page? EDIT x2: Seems to be on the right track, I have the error for: "Tag latest not found in repository .." so trying to figure that one out. Follow up: Read the tags section and saw no "latest" one so had to declare that specifically.

Either my Google skills went down the drain or there isn't a post for this. But, I cannot seem to find out how to setup a docker/template if I have a Dockerfile. Maybe I'm going with the wrong approach, but not sure. I would like to install this MineOS-Node : https://github.com/hexparrot/mineos-node There is a Dockerfile, but not sure what to do with it. I have Community Applications installed. Thank you for your help!