ubergeek

Members
  • Posts

    23
  • Joined

  • Last visited

Converted

  • Gender
    Undisclosed

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

ubergeek's Achievements

Noob

Noob (1/14)

0

Reputation

  1. A bit off this topic but since they are offering Carbonite discounts, any chance of a carbonite docker? I think they are windows only so probably not, just thought I would see what people are considering that might be comparable to CrashPlan. Very sad to see the unlimited home account go. I was only paying monthly $5.99 unlimited, therefore my access cannot be renewed any longer and will expire in approx 60 days. I am thinking of using this container and pay for Pro until I figure out the best way forward. Thanks for your work to help with migration! Sent from my iPhone using Tapatalk
  2. Those Noctuas are actually cooling your drives? I was told they wouldn't do much give the low static pressure but may reconsider trying a few. Sent from my iPhone using Tapatalk
  3. I just did a swap from a Norco 4020 into the same 846 case from the same seller you have listed. The 1200w psu's aren't that loud like the older ones, but I did swap mine with a 720w platinum PWS-721P-1R supermicro(non SQ) and it's even quieter (only $35 on eBay). I have active supermicro CPU coolers added and set IPMI fan setting on my X9 to optimum. The stock ACE 80 mid plane fans stay around 3k which I don't find too loud in my hallway closet but they aren't as quiet as my 120mm noctuas I had in the norco. I would try to stay as stock as possible if you can find a way as I really appreciate the SM engineered assemblies. You can get supermicro 80mm fan replacements for mid plane that are even quieter (FAN-0074L) that are used in the workstations (see fan matrix https://www.supermicro.com/support/resources/Thermal/ ) I think it's important to keep the static pressure to move the air through the backplane. My temps stay in the 28-35c range right now. With the 120mm noctuas in my norco I always was at high 30's and into 40's which I didn't like. I'd be interested to know what people are getting with the 120mm mod in the 846 case, but I really don't like the butchered look with the zip tied wall. If you can afford it though, definitely stay with the SM hot swap psu. The SQ series are almost silent from what I've seen but mine is quiet enough. I'm running two E5-2660 v1's in my X9 board with 96GB ecc ram currently and it rocks! I love my new SM chassis so much I just grabbed a 24 bay cse-216 and made it a jbod add on to the 846 via DAS sff-8087/8088 cables. Loving it! Sent from my iPhone using Tapatalk
  4. No, I will test with AV disabled though and whitelist added but I have also noticed dockers are running but cant manage or see them in GUI, only error: Fatal error: Uncaught UnexpectedValueException: RecursiveDirectoryIterator::__construct(/boot/config/plugins/dockerMan/templates-user): failed to open dir: Not a directory in /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php:63 Stack trace: #0 /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php(63): RecursiveDirectoryIterator->__construct('/boot/config/pl...', 4096) #1 /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php(92): DockerTemplates->listDir('/boot/config/pl...', 'xml') #2 /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php(222): DockerTemplates->getTemplates('all') #3 /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php(360): DockerTemplates->getTemplateValue('binhex/arch-cou...', 'Icon') #4 /usr/local/emhttp/plugins/dynamix.docker.manager/include/DockerClient.php(323): DockerTemplates->getIcon('binhex/arch-cou...') #5 /usr/local/emhttp/plugins/dynamix/include/DefaultPageLayout.php(383) : eval()'d code(7 in I see that several of my plugins failed to re-install properly, so I will attempt to repair those to correct. Includes community applications. Edit: re-installs not working either, looks like I may have had some corruption on USB, not sure. Going to test further. Reformatted USB, installed new files for 6.3.5, still cannot re-install community applications, getting error plugin: installing: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plgplugin: downloading https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plgplugin: downloading: https://raw.githubusercontent.com/Squidly271/community.applications/master/plugins/community.applications.plg ... doneCleaning Up Old Versionsplugin: downloading: https://raw.github.com/Squidly271/community.applications/master/archive/community.applications-2017.05.21.txz ... failed (Generic error)plugin: wget: https://raw.github.com/Squidly271/community.applications/master/archive/community.applications-2017.05.21.txz download failure (Generic error) Going to have to post in another thread I believe for support....
  5. Upgraded a a few days ago, notice the "Dashboard" tab is mostly blank on the gui now. Not sure if its related yet as I need to test further on this end.
  6. Hi @snoopy86 , I appreciate your LMS and emoncms containers. I have been trying to set up remote logging (as seen in links below) but there is no "emonhub" tab for the config to do so in your emoncms docker. The tab is usually under the Setup tab but is not there. Do you have any suggestions for exposing or editing the config? https://guide.openenergymonitor.org/setup/remote/ https://community.openenergymonitor.org/t/emoncms-running-on-own-server/1648
  7. So I still get this, and am tryiing to troubleshoot why my disks keep spinning up (I have cache_dirs and sleep process that is accessing disks)....anyway can this error be to blame or how can I remove this crontab -root command from making its way into the system?
  8. I would like to see a write up for unRaid as well, although I am concerned about memory and cpu. I have 4GB ram and an e3300 but already running several plugins....perhaps it's better to run on another host? I have a 1tb cache drive for what it's worth.
  9. /mnt/disk1 did not contain the directory Movies any longer, my move command must have moved it to /mnt/disk1/Photos....this was true on disks 1-5, but not disks 6-15.... curious as to how my mv /mnt/user/Movies /mnt/user/Photos command only moved the movies folders on those 5 disks... I have since moved the misplaced Movies directories back to their rightful home in /mnt/user...hoping I won't have any collateral issues...I moved them back individually on each affected disk.
  10. After further investigation I have found what I believe are the missing files in my Photos share...I really need to avoid shell commands late at night...I thought I was working on the remote server instead of my local when the trouble began. My question now would be this: If MOST but not ALL of my "Movies" directories are now inside of the "Photos" share, should I move back individually per disk or through user share? ie. mv /mnt/disk1/Photos/Movies /mnt/disk1/Movies or mv /mnt/user/Photos/Movies /mnt/disk1/Movies The original move occurred through user share, not sure why I have some movies left in the original Movies share... What is even more strange to me is that the Movies folder was left intact on several disks that also had the Photos folder present, yet it do not move the Movie folder inside it as it did on disks 1-5
  11. OK, I made a foolish mistake and accidelntally moved my Movies directory on a server. I was in a putty session over ssh, I promptly moved back in place but only a fractionof the movies are showing up in user share....the files were spread across multiple disks, but do not show when examining disks individually...the space being used is still the same on unMenu... What should I do next? Will a parity rebuild fix this?
  12. I have 5 of these that I got on the newegg deal @ 60 each...2 are in my whs, but I really wanted to use for unRaid...I flashed two of the empty ones with the japanese FW already...I wish we could have some sort of feedback to test the functionality of the new FW for corruption issues... I also did not preclear before assigning data drive and parity drive...can i unassign and preclear these still? I did set default to 4K aligned.