leech Posted January 16, 2011 Share Posted January 16, 2011 Hi Unraid 4.5.6 Mainboard: http://www.inpc.com.ua/data/product_f/miniitx/j7f4b.htm I try to tell you the hole timeline: My problem is that yesterday may unRaid crashed. After reboot it checked Parity. Ok should be. Today it's done i looked into the Web interface and all looks fine. But when i tried to access the SMB shares i got a timeout and the unraid isn't longer accessible. Also the web interface isn't reachable anymore. I also couldn't ping it. So i started to search about this problem. I found some who have the same problem as me where the problem was related to a read only usb stick. I tested write access to the flash but thats no problem. i can write the syslog and other stuff. also done checkdisc on the flash drive. I also deleted the HWADDR Line in the network.cfg I added a cache disc two days ago so i thought that may the problem, so i removed it. (there was no data on cause i forget to active the cache disc for the shares...) Unraid booted up but same problem. After some searching again i didn't find anything more which is related to my problem scenario. So i start some problem investigation for myself. My infos: Unraid boots up Web interface is up but it loads very slow telnet up but very slow (not usable) try to access smb - timeout, web interface gone local ping to unraid from windows machine - packetloss - see log below local ping to windows machine from unraid - packetloss - see log below local ping to router from unraid - sry no log but only "From 192.168.1.1 icmp_seq=52 Destination Host Unreachable" Unraid has gone from the routers "active device" list copy syslog to flash - see log below copy ifconfig to flash - see log below shutdown i have to say one thing. I got one curious thing. The Mac address of the eth0 interface was at first boot-up simply normal. But since the second boot it shows 00 for the first 4 pairs of digits and only for the last one the correct digits. In the log you see only 00:00:00... I didn't pay attention to this cause i couldn't change it and it looks like it isn't a problem since it works for weeks without problem. so here are the logs: syslog also attached syslog2.zip Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 windows ping: C:\Users\leech>ping 192.168.1.104 -t Ping wird ausgeführt für 192.168.1.104 mit 32 Bytes Daten: Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Antwort von 192.168.1.104: Bytes=32 Zeit<1ms TTL=64 Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Zeitüberschreitung der Anforderung. Zeitüberschreitung der Anforderung. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Antwort von 192.168.1.111: Zielhost nicht erreichbar. Ping-Statistik für 192.168.1.104: Pakete: Gesendet = 60, Empfangen = 32, Verloren = 28 (46% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 0ms, Maximum = 0ms, Mittelwert = 0ms STRG-C ^C Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 unraid ping: PING leech-pc (192.168.1.111) 56(84) bytes of data. 64 bytes from Leech-PC (192.168.1.111): icmp_seq=2 ttl=128 time=0.146 ms 64 bytes from 192.168.1.111: icmp_seq=4 ttl=128 time=0.122 ms 64 bytes from Leech-PC (192.168.1.111): icmp_seq=5 ttl=128 time=0.179 ms 64 bytes from 192.168.1.111: icmp_seq=7 ttl=128 time=0.162 ms 64 bytes from Leech-PC (192.168.1.111): icmp_seq=8 ttl=128 time=0.161 ms 64 bytes from Leech-PC (192.168.1.111): icmp_seq=10 ttl=128 time=0.137 ms 64 bytes from 192.168.1.111: icmp_seq=12 ttl=128 time=0.134 ms 64 bytes from Leech-PC (192.168.1.111): icmp_seq=13 ttl=128 time=0.160 ms 64 bytes from 192.168.1.111: icmp_seq=15 ttl=128 time=0.148 ms From 192.168.1.104 icmp_seq=50 Destination Host Unreachable From 192.168.1.104 icmp_seq=51 Destination Host Unreachable From 192.168.1.104 icmp_seq=52 Destination Host Unreachable From 192.168.1.104 icmp_seq=53 Destination Host Unreachable From 192.168.1.104 icmp_seq=54 Destination Host Unreachable From 192.168.1.104 icmp_seq=55 Destination Host Unreachable From 192.168.1.104 icmp_seq=56 Destination Host Unreachable From 192.168.1.104 icmp_seq=57 Destination Host Unreachable From 192.168.1.104 icmp_seq=58 Destination Host Unreachable --- leech-pc ping statistics --- 58 packets transmitted, 9 received, +9 errors, 84% packet loss, time 173599ms rtt min/avg/max/mdev = 0.122/0.149/0.179/0.023 ms, pipe 3 Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 Syslog: Jan 16 18:22:22 Tower syslogd 1.4.1: restart. Jan 16 18:22:22 Tower kernel: klogd 1.4.1, log source = /proc/kmsg started. Jan 16 18:22:22 Tower kernel: Linux version 2.6.32.9-unRAID (root@Develop) (gcc version 4.2.3) #5 SMP Wed Jun 16 20:45:26 MDT 2010 Jan 16 18:22:22 Tower kernel: KERNEL supported cpus: Jan 16 18:22:22 Tower kernel: Intel GenuineIntel Jan 16 18:22:22 Tower kernel: AMD AuthenticAMD Jan 16 18:22:22 Tower kernel: NSC Geode by NSC Jan 16 18:22:22 Tower kernel: Cyrix CyrixInstead Jan 16 18:22:22 Tower kernel: Centaur CentaurHauls Jan 16 18:22:22 Tower kernel: Transmeta GenuineTMx86 Jan 16 18:22:22 Tower kernel: Transmeta TransmetaCPU Jan 16 18:22:22 Tower kernel: UMC UMC UMC UMC Jan 16 18:22:22 Tower kernel: BIOS-provided physical RAM map: Jan 16 18:22:22 Tower kernel: BIOS-e820: 0000000000000000 - 000000000009d400 (usable) Jan 16 18:22:22 Tower kernel: BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved) Jan 16 18:22:22 Tower kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Jan 16 18:22:22 Tower kernel: BIOS-e820: 0000000000100000 - 000000001bee0000 (usable) Jan 16 18:22:22 Tower kernel: BIOS-e820: 000000001bee0000 - 000000001bee3000 (ACPI NVS) Jan 16 18:22:22 Tower kernel: BIOS-e820: 000000001bee3000 - 000000001bef0000 (ACPI data) Jan 16 18:22:22 Tower kernel: BIOS-e820: 000000001bef0000 - 000000001bf00000 (reserved) Jan 16 18:22:22 Tower kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jan 16 18:22:22 Tower kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jan 16 18:22:22 Tower kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Jan 16 18:22:22 Tower kernel: DMI 2.3 present. Jan 16 18:22:22 Tower kernel: Phoenix BIOS detected: BIOS may corrupt low RAM, working around it. Jan 16 18:22:22 Tower kernel: e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) Jan 16 18:22:22 Tower kernel: last_pfn = 0x1bee0 max_arch_pfn = 0x1000000 Jan 16 18:22:22 Tower kernel: MTRR default type: uncachable Jan 16 18:22:22 Tower kernel: MTRR fixed ranges enabled: Jan 16 18:22:22 Tower kernel: 00000-9FFFF write-back Jan 16 18:22:22 Tower kernel: A0000-BFFFF uncachable Jan 16 18:22:22 Tower kernel: C0000-CFFFF write-protect Jan 16 18:22:22 Tower kernel: D0000-EFFFF uncachable Jan 16 18:22:22 Tower kernel: F0000-F7FFF write-through Jan 16 18:22:22 Tower kernel: F8000-F8FFF uncachable Jan 16 18:22:22 Tower kernel: F9000-FFFFF write-through Jan 16 18:22:22 Tower kernel: MTRR variable ranges enabled: Jan 16 18:22:22 Tower kernel: 0 base 000000000 mask FE0000000 write-back Jan 16 18:22:22 Tower kernel: 1 base 01C000000 mask FFC000000 uncachable Jan 16 18:22:22 Tower kernel: 2 base 0E8000000 mask FF8000000 write-combining Jan 16 18:22:22 Tower kernel: 3 base 01BF00000 mask FFFF00000 uncachable Jan 16 18:22:22 Tower kernel: 4 disabled Jan 16 18:22:22 Tower kernel: 5 disabled Jan 16 18:22:22 Tower kernel: 6 disabled Jan 16 18:22:22 Tower kernel: 7 disabled Jan 16 18:22:22 Tower kernel: x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Jan 16 18:22:22 Tower kernel: initial memory mapped : 0 - 01800000 Jan 16 18:22:22 Tower kernel: init_memory_mapping: 0000000000000000-000000001bee0000 Jan 16 18:22:22 Tower kernel: NX (Execute Disable) protection: active Jan 16 18:22:22 Tower kernel: 0000000000 - 0000200000 page 4k Jan 16 18:22:22 Tower kernel: 0000200000 - 001be00000 page 2M Jan 16 18:22:22 Tower kernel: 001be00000 - 001bee0000 page 4k Jan 16 18:22:22 Tower kernel: kernel direct mapping tables up to 1bee0000 @ 10000-16000 Jan 16 18:22:22 Tower kernel: RAMDISK: 18aab000 - 1bedf09a Jan 16 18:22:22 Tower kernel: ACPI: RSDP 000f7dd0 00014 (v00 CN700 ) Jan 16 18:22:22 Tower kernel: ACPI: RSDT 1bee3000 00034 (v01 CN700 AWRDACPI 42302E31 AWRD 00000000) Jan 16 18:22:22 Tower kernel: ACPI: FACP 1bee3080 00074 (v01 CN700 AWRDACPI 42302E31 AWRD 00000000) Jan 16 18:22:22 Tower kernel: ACPI: DSDT 1bee3100 0547C (v01 CN700 AWRDACPI 00001000 MSFT 03000000) Jan 16 18:22:22 Tower kernel: ACPI: FACS 1bee0000 00040 Jan 16 18:22:22 Tower kernel: ACPI: _HPT 1bee8600 00038 (v01 CN700 AWRDACPI 42302E31 AWRD 00000098) Jan 16 18:22:22 Tower kernel: ACPI: _WDT 1bee8640 00047 (v01 CN700 AWRDACPI 42302E31 AWRD 00000000) Jan 16 18:22:22 Tower kernel: ACPI: APIC 1bee8580 0005A (v01 CN700 AWRDACPI 42302E31 AWRD 00000000) Jan 16 18:22:22 Tower kernel: ACPI: Local APIC address 0xfee00000 Jan 16 18:22:22 Tower kernel: 0MB HIGHMEM available. Jan 16 18:22:22 Tower kernel: 446MB LOWMEM available. Jan 16 18:22:22 Tower kernel: mapped low ram: 0 - 1bee0000 Jan 16 18:22:22 Tower kernel: low ram: 0 - 1bee0000 Jan 16 18:22:22 Tower kernel: node 0 low ram: 00000000 - 1bee0000 Jan 16 18:22:22 Tower kernel: node 0 bootmap 00012000 - 000157dc Jan 16 18:22:22 Tower kernel: (9 early reservations) ==> bootmem [0000000000 - 001bee0000] Jan 16 18:22:22 Tower kernel: #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Jan 16 18:22:22 Tower kernel: #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] Jan 16 18:22:22 Tower kernel: #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] Jan 16 18:22:22 Tower kernel: #3 [0001000000 - 0001481c4c] TEXT DATA BSS ==> [0001000000 - 0001481c4c] Jan 16 18:22:22 Tower kernel: #4 [0018aab000 - 001bedf09a] RAMDISK ==> [0018aab000 - 001bedf09a] Jan 16 18:22:22 Tower kernel: #5 [000009c000 - 0000100000] BIOS reserved ==> [000009c000 - 0000100000] Jan 16 18:22:22 Tower kernel: #6 [0001482000 - 000148e06e] BRK ==> [0001482000 - 000148e06e] Jan 16 18:22:22 Tower kernel: #7 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000] Jan 16 18:22:22 Tower kernel: #8 [0000012000 - 0000016000] BOOTMAP ==> [0000012000 - 0000016000] Jan 16 18:22:22 Tower kernel: found SMP MP-table at [c00f3c30] f3c30 Jan 16 18:22:22 Tower kernel: Zone PFN ranges: Jan 16 18:22:22 Tower kernel: DMA 0x00000010 -> 0x00001000 Jan 16 18:22:22 Tower kernel: Normal 0x00001000 -> 0x0001bee0 Jan 16 18:22:22 Tower kernel: HighMem 0x0001bee0 -> 0x0001bee0 Jan 16 18:22:22 Tower kernel: Movable zone start PFN for each node Jan 16 18:22:22 Tower kernel: early_node_map[2] active PFN ranges Jan 16 18:22:22 Tower kernel: 0: 0x00000010 -> 0x0000009d Jan 16 18:22:22 Tower kernel: 0: 0x00000100 -> 0x0001bee0 Jan 16 18:22:22 Tower kernel: On node 0 totalpages: 114285 Jan 16 18:22:22 Tower kernel: free_area_init_node: node 0, pgdat c13f0fc0, node_mem_map c1490200 Jan 16 18:22:22 Tower kernel: DMA zone: 32 pages used for memmap Jan 16 18:22:22 Tower kernel: DMA zone: 0 pages reserved Jan 16 18:22:22 Tower kernel: DMA zone: 3949 pages, LIFO batch:0 Jan 16 18:22:22 Tower kernel: Normal zone: 862 pages used for memmap Jan 16 18:22:22 Tower kernel: Normal zone: 109442 pages, LIFO batch:31 Jan 16 18:22:22 Tower kernel: Using APIC driver default Jan 16 18:22:22 Tower kernel: ACPI: PM-Timer IO Port: 0x408 Jan 16 18:22:22 Tower kernel: ACPI: Local APIC address 0xfee00000 Jan 16 18:22:22 Tower kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Jan 16 18:22:22 Tower kernel: ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) Jan 16 18:22:22 Tower kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) Jan 16 18:22:22 Tower kernel: IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 Jan 16 18:22:22 Tower kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Jan 16 18:22:22 Tower kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Jan 16 18:22:22 Tower kernel: ACPI: IRQ0 used by override. Jan 16 18:22:22 Tower kernel: ACPI: IRQ2 used by override. Jan 16 18:22:22 Tower kernel: ACPI: IRQ9 used by override. Jan 16 18:22:22 Tower kernel: Enabling APIC mode: Flat. Using 1 I/O APICs Jan 16 18:22:22 Tower kernel: Using ACPI (MADT) for SMP configuration information Jan 16 18:22:22 Tower kernel: SMP: Allowing 1 CPUs, 0 hotplug CPUs Jan 16 18:22:22 Tower kernel: nr_irqs_gsi: 24 Jan 16 18:22:22 Tower kernel: Allocating PCI resources starting at 1bf00000 (gap: 1bf00000:e2d00000) Jan 16 18:22:22 Tower kernel: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:1 nr_node_ids:1 Jan 16 18:22:22 Tower kernel: PERCPU: Embedded 11 pages/cpu @c1a00000 s22232 r0 d22824 u2097152 Jan 16 18:22:22 Tower kernel: pcpu-alloc: s22232 r0 d22824 u2097152 alloc=1*2097152 Jan 16 18:22:22 Tower kernel: pcpu-alloc: [0] 0 Jan 16 18:22:22 Tower kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113391 Jan 16 18:22:22 Tower kernel: Kernel command line: initrd=bzroot BOOT_IMAGE=bzimage Jan 16 18:22:22 Tower kernel: PID hash table entries: 2048 (order: 1, 8192 bytes) Jan 16 18:22:22 Tower kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Jan 16 18:22:22 Tower kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Jan 16 18:22:22 Tower kernel: Enabling fast FPU save and restore... done. Jan 16 18:22:22 Tower kernel: Enabling unmasked SIMD FPU exception support... done. Jan 16 18:22:22 Tower kernel: Initializing CPU#0 Jan 16 18:22:22 Tower kernel: Initializing HighMem for node 0 (00000000:00000000) Jan 16 18:22:22 Tower kernel: Memory: 394776k/457600k available (2692k kernel code, 62200k reserved, 1359k data, 312k init, 0k highmem) Jan 16 18:22:22 Tower kernel: virtual kernel memory layout: Jan 16 18:22:22 Tower kernel: fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB) Jan 16 18:22:22 Tower kernel: pkmap : 0xffa00000 - 0xffc00000 (2048 kB) Jan 16 18:22:22 Tower kernel: vmalloc : 0xdc6e0000 - 0xff9fe000 ( 563 MB) Jan 16 18:22:22 Tower kernel: lowmem : 0xc0000000 - 0xdbee0000 ( 446 MB) Jan 16 18:22:22 Tower kernel: .init : 0xc13f5000 - 0xc1443000 ( 312 kB) Jan 16 18:22:22 Tower kernel: .data : 0xc12a12ac - 0xc13f4eec (1359 kB) Jan 16 18:22:22 Tower kernel: .text : 0xc1000000 - 0xc12a12ac (2692 kB) Jan 16 18:22:22 Tower kernel: Checking if this processor honours the WP bit even in supervisor mode...Ok. Jan 16 18:22:22 Tower kernel: SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Jan 16 18:22:22 Tower kernel: Hierarchical RCU implementation. Jan 16 18:22:22 Tower kernel: NR_IRQS:384 Jan 16 18:22:22 Tower kernel: Console: colour VGA+ 80x25 Jan 16 18:22:22 Tower kernel: console [tty0] enabled Jan 16 18:22:22 Tower kernel: Fast TSC calibration using PIT Jan 16 18:22:22 Tower kernel: Detected 1200.244 MHz processor. Jan 16 18:22:22 Tower kernel: Calibrating delay loop (skipped), value calculated using timer frequency.. 2400.48 BogoMIPS (lpj=12002440) Jan 16 18:22:22 Tower kernel: Mount-cache hash table entries: 512 Jan 16 18:22:22 Tower kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Jan 16 18:22:22 Tower kernel: CPU: L2 Cache: 128K (64 bytes/line) Jan 16 18:22:22 Tower kernel: Checking 'hlt' instruction... OK. Jan 16 18:22:22 Tower kernel: SMP alternatives: switching to UP code Jan 16 18:22:22 Tower kernel: Freeing SMP alternatives: 14k freed Jan 16 18:22:22 Tower kernel: ACPI: Core revision 20090903 Jan 16 18:22:22 Tower kernel: ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Jan 16 18:22:22 Tower kernel: CPU0: Centaur VIA Eden Processor 1200MHz stepping 00 Jan 16 18:22:22 Tower kernel: Brought up 1 CPUs Jan 16 18:22:22 Tower kernel: Total of 1 processors activated (2400.48 BogoMIPS). Jan 16 18:22:22 Tower kernel: NET: Registered protocol family 16 Jan 16 18:22:22 Tower kernel: ACPI: bus type pci registered Jan 16 18:22:22 Tower kernel: PCI: PCI BIOS revision 2.10 entry at 0xfa390, last bus=1 Jan 16 18:22:22 Tower kernel: PCI: Using configuration type 1 for base access Jan 16 18:22:22 Tower kernel: bio: create slab <bio-0> at 0 Jan 16 18:22:22 Tower kernel: ACPI: EC: Look up EC in DSDT Jan 16 18:22:22 Tower kernel: ACPI Warning: Package List length (0x8) larger than NumElements count (0x2), truncated Jan 16 18:22:22 Tower kernel: (20090903/dsobject-515) Jan 16 18:22:22 Tower kernel: ACPI Warning: Package List length (0x8) larger than NumElements count (0x2), truncated Jan 16 18:22:22 Tower kernel: (20090903/dsobject-515) Jan 16 18:22:22 Tower kernel: ACPI: Interpreter enabled Jan 16 18:22:22 Tower kernel: ACPI: (supports S0 S1 S5) Jan 16 18:22:22 Tower kernel: ACPI: Using IOAPIC for interrupt routing Jan 16 18:22:22 Tower kernel: ACPI: No dock devices found. Jan 16 18:22:22 Tower kernel: ACPI: PCI Root Bridge [PCI0] (0000:00) Jan 16 18:22:22 Tower kernel: pci 0000:00:00.0: reg 10 32bit mmio pref: [0xe8000000-0xefffffff] Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: supports D1 Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 10 io port: [0xff00-0xff07] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 14 io port: [0xfe00-0xfe03] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 18 io port: [0xfd00-0xfd07] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 1c io port: [0xfc00-0xfc03] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 20 io port: [0xfb00-0xfb0f] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 24 32bit mmio: [0xfdfff000-0xfdfff3ff] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: reg 30 32bit mmio pref: [0x000000-0x07ffff] Jan 16 18:22:22 Tower kernel: pci 0000:00:08.0: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: reg 10 io port: [0xea00-0xeaff] Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: reg 14 32bit mmio: [0xfdffe000-0xfdffe0ff] Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: reg 30 32bit mmio pref: [0x000000-0x01ffff] Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:09.0: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: reg 10 io port: [0xec00-0xecff] Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: reg 14 32bit mmio: [0xfdffd000-0xfdffd0ff] Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: reg 30 32bit mmio pref: [0x000000-0x01ffff] Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: PME# supported from D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:0b.0: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 10 io port: [0xfa00-0xfa07] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 14 io port: [0xf900-0xf903] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 18 io port: [0xf800-0xf807] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 1c io port: [0xf700-0xf703] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 20 io port: [0xf600-0xf60f] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.0: reg 24 io port: [0xee00-0xeeff] Jan 16 18:22:22 Tower kernel: pci 0000:00:0f.1: reg 20 io port: [0xf500-0xf50f] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.0: reg 20 io port: [0xf400-0xf41f] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.0: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:10.0: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:10.1: reg 20 io port: [0xf300-0xf31f] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.1: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:10.1: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:10.2: reg 20 io port: [0xf200-0xf21f] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.2: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:10.2: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:10.3: reg 20 io port: [0xf100-0xf11f] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.3: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:10.3: PME# disabled Jan 16 18:22:22 Tower kernel: pci 0000:00:10.4: reg 10 32bit mmio: [0xfdffc000-0xfdffc0ff] Jan 16 18:22:22 Tower kernel: pci 0000:00:10.4: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold Jan 16 18:22:22 Tower kernel: pci 0000:00:10.4: PME# disabled Jan 16 18:22:22 Tower kernel: HPET not enabled in BIOS. You might try hpet=force boot option Jan 16 18:22:22 Tower kernel: pci 0000:00:11.5: reg 10 io port: [0xe800-0xe8ff] Jan 16 18:22:22 Tower kernel: pci 0000:00:11.5: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:01:00.0: reg 10 32bit mmio pref: [0xf4000000-0xf7ffffff] Jan 16 18:22:22 Tower kernel: pci 0000:01:00.0: reg 14 32bit mmio: [0xfb000000-0xfbffffff] Jan 16 18:22:22 Tower kernel: pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] Jan 16 18:22:22 Tower kernel: pci 0000:01:00.0: supports D1 D2 Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: bridge io port: [0xd000-0xdfff] Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: bridge 32bit mmio: [0xfb000000-0xfcffffff] Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: bridge 32bit mmio pref: [0xf4000000-0xf7ffffff] Jan 16 18:22:22 Tower kernel: pci_bus 0000:00: on NUMA node 0 Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5 Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 2nd part Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKA] (IRQs *20) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKB] (IRQs *21) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKC] (IRQs *22) Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled. Jan 16 18:22:22 Tower kernel: vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none Jan 16 18:22:22 Tower kernel: vgaarb: loaded Jan 16 18:22:22 Tower kernel: SCSI subsystem initialized Jan 16 18:22:22 Tower kernel: libata version 3.00 loaded. Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver usbfs Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver hub Jan 16 18:22:22 Tower kernel: usbcore: registered new device driver usb Jan 16 18:22:22 Tower kernel: PCI: Using ACPI for IRQ routing Jan 16 18:22:22 Tower kernel: Switching to clocksource tsc Jan 16 18:22:22 Tower kernel: pnp: PnP ACPI init Jan 16 18:22:22 Tower kernel: ACPI: bus type pnp registered Jan 16 18:22:22 Tower kernel: pnp: PnP ACPI: found 12 devices Jan 16 18:22:22 Tower kernel: ACPI: ACPI bus type pnp unregistered Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xf0000-0xfffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xfe800000-0xfe8000ff has been reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xfea00000-0xfea000ff has been reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0x1bee0000-0x1befffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xffff0000-0xffffffff has been reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0x0-0x9ffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0x100000-0x1bedffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xfec00000-0xfecfffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved Jan 16 18:22:22 Tower kernel: system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved Jan 16 18:22:22 Tower kernel: system 00:02: ioport range 0x400-0x47f has been reserved Jan 16 18:22:22 Tower kernel: system 00:02: ioport range 0x500-0x50f has been reserved Jan 16 18:22:22 Tower kernel: system 00:03: iomem range 0xfea00000-0xfea000ff has been reserved Jan 16 18:22:22 Tower kernel: system 00:04: ioport range 0x4d0-0x4d1 has been reserved Jan 16 18:22:22 Tower kernel: system 00:04: ioport range 0x800-0x805 has been reserved Jan 16 18:22:22 Tower kernel: system 00:04: ioport range 0x290-0x297 has been reserved Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: IO window: 0xd000-0xdfff Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: MEM window: 0xfb000000-0xfcffffff Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: PREFETCH window: 0xf4000000-0xf7ffffff Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: setting latency timer to 64 Jan 16 18:22:22 Tower kernel: pci_bus 0000:00: resource 0 io: [0x00-0xffff] Jan 16 18:22:22 Tower kernel: pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] Jan 16 18:22:22 Tower kernel: pci_bus 0000:01: resource 0 io: [0xd000-0xdfff] Jan 16 18:22:22 Tower kernel: pci_bus 0000:01: resource 1 mem: [0xfb000000-0xfcffffff] Jan 16 18:22:22 Tower kernel: pci_bus 0000:01: resource 2 pref mem [0xf4000000-0xf7ffffff] Jan 16 18:22:22 Tower kernel: NET: Registered protocol family 2 Jan 16 18:22:22 Tower kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes) Jan 16 18:22:22 Tower kernel: TCP established hash table entries: 16384 (order: 5, 131072 bytes) Jan 16 18:22:22 Tower kernel: TCP bind hash table entries: 16384 (order: 5, 131072 bytes) Jan 16 18:22:22 Tower kernel: TCP: Hash tables configured (established 16384 bind 16384) Jan 16 18:22:22 Tower kernel: TCP reno registered Jan 16 18:22:22 Tower kernel: NET: Registered protocol family 1 Jan 16 18:22:22 Tower kernel: RPC: Registered udp transport module. Jan 16 18:22:22 Tower kernel: RPC: Registered tcp transport module. Jan 16 18:22:22 Tower kernel: RPC: Registered tcp NFSv4.1 backchannel transport module. Jan 16 18:22:22 Tower kernel: pci 0000:00:01.0: disabling DAC on VIA PCI bridge Jan 16 18:22:22 Tower kernel: pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message Jan 16 18:22:22 Tower kernel: pci 0000:01:00.0: Boot video device Jan 16 18:22:22 Tower kernel: Unpacking initramfs... Jan 16 18:22:22 Tower kernel: Freeing initrd memory: 53456k freed Jan 16 18:22:22 Tower kernel: Installing knfsd (copyright (C) 1996 [email protected]). Jan 16 18:22:22 Tower kernel: Slow work thread pool: Starting up Jan 16 18:22:22 Tower kernel: Slow work thread pool: Ready Jan 16 18:22:22 Tower kernel: fuse init (API version 7.13) Jan 16 18:22:22 Tower kernel: msgmni has been set to 875 Jan 16 18:22:22 Tower kernel: io scheduler noop registered (default) Jan 16 18:22:22 Tower kernel: io scheduler anticipatory registered Jan 16 18:22:22 Tower kernel: io scheduler deadline registered Jan 16 18:22:22 Tower kernel: io scheduler cfq registered Jan 16 18:22:22 Tower kernel: input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 Jan 16 18:22:22 Tower kernel: ACPI: Power Button [PWRB] Jan 16 18:22:22 Tower kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 Jan 16 18:22:22 Tower kernel: ACPI: Power Button [PWRF] Jan 16 18:22:22 Tower kernel: fan PNP0C0B:00: registered as cooling_device0 Jan 16 18:22:22 Tower kernel: ACPI: Fan [FAN] (on) Jan 16 18:22:22 Tower kernel: Marking TSC unstable due to TSC halts in idle Jan 16 18:22:22 Tower kernel: Switching to clocksource acpi_pm Jan 16 18:22:22 Tower kernel: processor LNXCPU:00: registered as cooling_device1 Jan 16 18:22:22 Tower kernel: thermal LNXTHERM:01: registered as thermal_zone0 Jan 16 18:22:22 Tower kernel: ACPI: Thermal Zone [THRM] (40 C) Jan 16 18:22:22 Tower kernel: lp: driver loaded but no devices found Jan 16 18:22:22 Tower kernel: Real Time Clock Driver v1.12b Jan 16 18:22:22 Tower kernel: VIA RNG detected Jan 16 18:22:22 Tower kernel: Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Jan 16 18:22:22 Tower kernel: Hangcheck: Using get_cycles(). Jan 16 18:22:22 Tower kernel: Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled Jan 16 18:22:22 Tower kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jan 16 18:22:22 Tower kernel: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jan 16 18:22:22 Tower kernel: serial 00:0a: disabled Jan 16 18:22:22 Tower kernel: parport_pc 00:0b: reported by Plug and Play ACPI Jan 16 18:22:22 Tower kernel: parport0: PC-style at 0x378, irq 7 [PCSPP(,...)] Jan 16 18:22:22 Tower kernel: lp0: using parport0 (interrupt-driven). Jan 16 18:22:22 Tower kernel: floppy0: no floppy controllers found Jan 16 18:22:22 Tower kernel: loop: module loaded Jan 16 18:22:22 Tower kernel: Uniform Multi-Platform E-IDE driver Jan 16 18:22:22 Tower kernel: e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI Jan 16 18:22:22 Tower kernel: e100: Copyright(c) 1999-2006 Intel Corporation Jan 16 18:22:22 Tower kernel: Broadcom NetXtreme II CNIC Driver cnic v2.0.1 (Oct 01, 2009) Jan 16 18:22:22 Tower kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21 Jan 16 18:22:22 Tower kernel: ehci_hcd 0000:00:10.4: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 Jan 16 18:22:22 Tower kernel: ehci_hcd 0000:00:10.4: EHCI Host Controller Jan 16 18:22:22 Tower kernel: ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 Jan 16 18:22:22 Tower kernel: ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdffc000 Jan 16 18:22:22 Tower kernel: ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00 Jan 16 18:22:22 Tower kernel: usb usb1: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: hub 1-0:1.0: USB hub found Jan 16 18:22:22 Tower kernel: hub 1-0:1.0: 8 ports detected Jan 16 18:22:22 Tower kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Jan 16 18:22:22 Tower kernel: uhci_hcd: USB Universal Host Controller Interface driver Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.0: UHCI Host Controller Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.0: irq 21, io base 0x0000f400 Jan 16 18:22:22 Tower kernel: usb usb2: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: hub 2-0:1.0: USB hub found Jan 16 18:22:22 Tower kernel: hub 2-0:1.0: 2 ports detected Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.1: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.1: UHCI Host Controller Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.1: irq 21, io base 0x0000f300 Jan 16 18:22:22 Tower kernel: usb usb3: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: hub 3-0:1.0: USB hub found Jan 16 18:22:22 Tower kernel: hub 3-0:1.0: 2 ports detected Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.2: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.2: UHCI Host Controller Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.2: irq 21, io base 0x0000f200 Jan 16 18:22:22 Tower kernel: usb usb4: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: hub 4-0:1.0: USB hub found Jan 16 18:22:22 Tower kernel: hub 4-0:1.0: 2 ports detected Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.3: UHCI Host Controller Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 Jan 16 18:22:22 Tower kernel: uhci_hcd 0000:00:10.3: irq 21, io base 0x0000f100 Jan 16 18:22:22 Tower kernel: usb usb5: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: hub 5-0:1.0: USB hub found Jan 16 18:22:22 Tower kernel: hub 5-0:1.0: 2 ports detected Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver usblp Jan 16 18:22:22 Tower kernel: Initializing USB Mass Storage driver... Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver usb-storage Jan 16 18:22:22 Tower kernel: USB Mass Storage support registered. Jan 16 18:22:22 Tower kernel: PNP: No PS/2 controller found. Probing ports directly. Jan 16 18:22:22 Tower kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Jan 16 18:22:22 Tower kernel: mice: PS/2 mouse device common for all mice Jan 16 18:22:22 Tower kernel: input: PC Speaker as /devices/platform/pcspkr/input/input2 Jan 16 18:22:22 Tower kernel: cpuidle: using governor ladder Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver hiddev Jan 16 18:22:22 Tower kernel: usbcore: registered new interface driver usbhid Jan 16 18:22:22 Tower kernel: usbhid: v2.6:USB HID core driver Jan 16 18:22:22 Tower kernel: TCP cubic registered Jan 16 18:22:22 Tower kernel: NET: Registered protocol family 17 Jan 16 18:22:22 Tower kernel: Using IPI No-Shortcut mode Jan 16 18:22:22 Tower kernel: Freeing unused kernel memory: 312k freed Jan 16 18:22:22 Tower kernel: usb 1-7: new high speed USB device using ehci_hcd and address 3 Jan 16 18:22:22 Tower kernel: usb 1-7: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: scsi0 : SCSI emulation for USB Mass Storage devices Jan 16 18:22:22 Tower kernel: usb-storage: device found at 3 Jan 16 18:22:22 Tower kernel: usb-storage: waiting for device to settle before scanning Jan 16 18:22:22 Tower kernel: usb 3-1: new low speed USB device using uhci_hcd and address 2 Jan 16 18:22:22 Tower kernel: usb 3-1: configuration #1 chosen from 1 choice Jan 16 18:22:22 Tower kernel: input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.0/input/input3 Jan 16 18:22:22 Tower kernel: generic-usb 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:10.1-1/input0 Jan 16 18:22:22 Tower kernel: sata_sil 0000:00:08.0: version 2.4 Jan 16 18:22:22 Tower kernel: sata_sil 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 Jan 16 18:22:22 Tower kernel: sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix Jan 16 18:22:22 Tower kernel: scsi1 : sata_sil Jan 16 18:22:22 Tower kernel: scsi2 : sata_sil Jan 16 18:22:22 Tower kernel: scsi3 : sata_sil Jan 16 18:22:22 Tower kernel: scsi4 : sata_sil Jan 16 18:22:22 Tower kernel: ata1: SATA max UDMA/100 mmio m1024@0xfdfff000 tf 0xfdfff080 irq 17 Jan 16 18:22:22 Tower kernel: ata2: SATA max UDMA/100 mmio m1024@0xfdfff000 tf 0xfdfff0c0 irq 17 Jan 16 18:22:22 Tower kernel: ata3: SATA max UDMA/100 mmio m1024@0xfdfff000 tf 0xfdfff280 irq 17 Jan 16 18:22:22 Tower kernel: ata4: SATA max UDMA/100 mmio m1024@0xfdfff000 tf 0xfdfff2c0 irq 17 Jan 16 18:22:22 Tower kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Jan 16 18:22:22 Tower kernel: ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata1.00: configured for UDMA/100 Jan 16 18:22:22 Tower kernel: scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Jan 16 18:22:22 Tower kernel: sd 1:0:0:0: [sda] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sda: sda1 Jan 16 18:22:22 Tower kernel: sd 1:0:0:0: [sda] Attached SCSI disk Jan 16 18:22:22 Tower kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Jan 16 18:22:22 Tower kernel: ata2.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata2.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata2.00: configured for UDMA/100 Jan 16 18:22:22 Tower kernel: scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 2:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Jan 16 18:22:22 Tower kernel: sd 2:0:0:0: [sdb] Write Protect is off Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 3rd part Jan 16 18:22:22 Tower kernel: sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sdb: sdb1 Jan 16 18:22:22 Tower kernel: sd 2:0:0:0: [sdb] Attached SCSI disk Jan 16 18:22:22 Tower kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Jan 16 18:22:22 Tower kernel: ata3.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata3.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata3.00: configured for UDMA/100 Jan 16 18:22:22 Tower kernel: scsi 3:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 3:0:0:0: [sdc] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) Jan 16 18:22:22 Tower kernel: sd 3:0:0:0: [sdc] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sdc: sdc1 Jan 16 18:22:22 Tower kernel: sd 3:0:0:0: [sdc] Attached SCSI disk Jan 16 18:22:22 Tower kernel: ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Jan 16 18:22:22 Tower kernel: ata4.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata4.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata4.00: configured for UDMA/100 Jan 16 18:22:22 Tower kernel: scsi 4:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 4:0:0:0: [sdd] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) Jan 16 18:22:22 Tower kernel: sd 4:0:0:0: [sdd] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sdd: sdd1 Jan 16 18:22:22 Tower kernel: sd 4:0:0:0: [sdd] Attached SCSI disk Jan 16 18:22:22 Tower kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded Jan 16 18:22:22 Tower kernel: r8169 0000:00:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jan 16 18:22:22 Tower kernel: r8169 0000:00:09.0: PCI: Disallowing DAC for device Jan 16 18:22:22 Tower kernel: r8169 0000:00:09.0: no PCI Express capability Jan 16 18:22:22 Tower kernel: eth0: RTL8169sc/8110sc at 0xdc744000, 00:00:00:00:09:a9, XID 18000000 IRQ 18 Jan 16 18:22:22 Tower kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded Jan 16 18:22:22 Tower kernel: r8169 0000:00:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 Jan 16 18:22:22 Tower kernel: r8169 0000:00:0b.0: PCI: Disallowing DAC for device Jan 16 18:22:22 Tower kernel: r8169 0000:00:0b.0: no PCI Express capability Jan 16 18:22:22 Tower kernel: eth1: RTL8169sc/8110sc at 0xdc748000, 00:00:00:00:09:aa, XID 18000000 IRQ 19 Jan 16 18:22:22 Tower kernel: sata_via 0000:00:0f.0: version 2.4 Jan 16 18:22:22 Tower kernel: ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20 Jan 16 18:22:22 Tower kernel: sata_via 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20 Jan 16 18:22:22 Tower kernel: sata_via 0000:00:0f.0: routed to hard irq line 11 Jan 16 18:22:22 Tower kernel: scsi5 : sata_via Jan 16 18:22:22 Tower kernel: scsi6 : sata_via Jan 16 18:22:22 Tower kernel: ata5: SATA max UDMA/133 cmd 0xfa00 ctl 0xf900 bmdma 0xf600 irq 20 Jan 16 18:22:22 Tower kernel: ata6: SATA max UDMA/133 cmd 0xf800 ctl 0xf700 bmdma 0xf608 irq 20 Jan 16 18:22:22 Tower kernel: ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jan 16 18:22:22 Tower kernel: scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2 Jan 16 18:22:22 Tower kernel: usb-storage: device scan complete Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] 3989504 512-byte logical blocks: (2.04 GB/1.90 GiB) Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Mode Sense: 03 00 00 00 Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Assuming drive cache: write through Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Assuming drive cache: write through Jan 16 18:22:22 Tower kernel: sde: Jan 16 18:22:22 Tower kernel: ata5.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata5.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata5.00: configured for UDMA/133 Jan 16 18:22:22 Tower kernel: scsi 5:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 5:0:0:0: [sdf] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) Jan 16 18:22:22 Tower kernel: sd 5:0:0:0: [sdf] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sdf: sdf1 Jan 16 18:22:22 Tower kernel: sd 5:0:0:0: [sdf] Attached SCSI disk Jan 16 18:22:22 Tower kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jan 16 18:22:22 Tower kernel: sde1 Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Assuming drive cache: write through Jan 16 18:22:22 Tower kernel: sd 0:0:0:0: [sde] Attached SCSI removable disk Jan 16 18:22:22 Tower kernel: ata6.00: ATA-8: ST31500341AS, CC1H, max UDMA/133 Jan 16 18:22:22 Tower kernel: ata6.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 0/32) Jan 16 18:22:22 Tower kernel: ata6.00: configured for UDMA/133 Jan 16 18:22:22 Tower kernel: scsi 6:0:0:0: Direct-Access ATA ST31500341AS CC1H PQ: 0 ANSI: 5 Jan 16 18:22:22 Tower kernel: sd 6:0:0:0: [sdg] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) Jan 16 18:22:22 Tower kernel: sd 6:0:0:0: [sdg] Write Protect is off Jan 16 18:22:22 Tower kernel: sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00 Jan 16 18:22:22 Tower kernel: sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 16 18:22:22 Tower kernel: sdg: sdg1 Jan 16 18:22:22 Tower kernel: sd 6:0:0:0: [sdg] Attached SCSI disk Jan 16 18:22:22 Tower kernel: via82cxxx 0000:00:0f.1: VIA vt8237 (rev 00) IDE UDMA133 Jan 16 18:22:22 Tower kernel: via82cxxx 0000:00:0f.1: IDE controller (0x1106:0x0571 rev 0x06) Jan 16 18:22:22 Tower kernel: VIA_IDE 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20 Jan 16 18:22:22 Tower kernel: via82cxxx 0000:00:0f.1: IDE port disabled Jan 16 18:22:22 Tower kernel: via82cxxx 0000:00:0f.1: not 100%% native mode: will probe irqs later Jan 16 18:22:22 Tower kernel: ide0: BM-DMA at 0xf500-0xf507 Jan 16 18:22:22 Tower kernel: Probing IDE interface ide0... Jan 16 18:22:22 Tower kernel: hda: SAMSUNG HA250JC, ATA DISK drive Jan 16 18:22:22 Tower kernel: hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 Jan 16 18:22:22 Tower kernel: hda: UDMA/100 mode selected Jan 16 18:22:22 Tower kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jan 16 18:22:22 Tower kernel: ide-gd driver 1.18 Jan 16 18:22:22 Tower kernel: hda: max request size: 512KiB Jan 16 18:22:22 Tower kernel: hda: 488397168 sectors (250059 MB) w/2048KiB Cache, CHS=30401/255/63 Jan 16 18:22:22 Tower kernel: hda: cache flushes supported Jan 16 18:22:22 Tower kernel: hda: hda1 Jan 16 18:22:22 Tower logger: /etc/rc.d/rc.inet1: /sbin/ifconfig lo 127.0.0.1 Jan 16 18:22:22 Tower logger: /etc/rc.d/rc.inet1: /sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: ifplugd 0.28 initializing. Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: Using interface eth0/00:00:00:00:09:A9 with driver <r8169> (version: 2.3LK-NAPI) Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: Using detection mode: SIOCETHTOOL Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: Initialization complete, link beat detected. Jan 16 18:22:22 Tower kernel: r8169: eth0: link up Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: Executing '/etc/ifplugd/ifplugd.action eth0 up'. Jan 16 18:22:22 Tower logger: /etc/rc.d/rc.inet1: /sbin/ifconfig eth0 hw ether 00:00:00:00:09:A9 Jan 16 18:22:22 Tower logger: /etc/rc.d/rc.inet1: /sbin/ifconfig eth0 192.168.1.104 broadcast 192.168.1.255 netmask 255.255.255.0 Jan 16 18:22:22 Tower logger: /etc/rc.d/rc.inet1: /sbin/route add default gw 192.168.1.1 metric 1 Jan 16 18:22:22 Tower ifplugd(eth0)[1250]: Program executed successfully. Jan 16 18:22:22 Tower rpc.statd[1299]: Version 1.1.4 Starting Jan 16 18:22:23 Tower emhttp: unRAID System Management Utility version 4.5.6 Jan 16 18:22:23 Tower emhttp: Copyright (C) 2005-2010, Lime Technology, LLC Jan 16 18:22:23 Tower emhttp: Plus key detected, GUID: 058F-6387-0000-000090903515 Jan 16 18:22:23 Tower emhttp: shcmd (1): udevadm settle Jan 16 18:22:23 Tower emhttp: Device inventory: Jan 16 18:22:23 Tower emhttp: pci-0000:00:08.0-scsi-0:0:0:0 host1 (sda) SAMSUNG_HD204UI_S2H7J1BZ912498 Jan 16 18:22:23 Tower emhttp: pci-0000:00:08.0-scsi-1:0:0:0 host2 (sdb) SAMSUNG_HD204UI_S2H7J1BZ912537 Jan 16 18:22:23 Tower emhttp: pci-0000:00:08.0-scsi-2:0:0:0 host3 (sdc) ST31500341AS_9VS1F4RS Jan 16 18:22:23 Tower emhttp: pci-0000:00:08.0-scsi-3:0:0:0 host4 (sdd) ST31500341AS_9VS1G56A Jan 16 18:22:23 Tower emhttp: pci-0000:00:0f.0-scsi-0:0:0:0 host5 (sdf) ST31500341AS_9VS1G6RX Jan 16 18:22:23 Tower emhttp: pci-0000:00:0f.0-scsi-1:0:0:0 host6 (sdg) ST31500341AS_9VS1JV6V Jan 16 18:22:23 Tower emhttp: pci-0000:00:0f.1-ide-0:0 ide0 (hda) SAMSUNG_HA250JC_S094J10L411996 Jan 16 18:22:23 Tower emhttp: shcmd (2): modprobe -rw md-mod 2>&1 | logger Jan 16 18:22:23 Tower emhttp: shcmd (3): modprobe md-mod super=/boot/config/super.dat slots=8,0,8,16,8,48,8,32,8,96,8,80 2>&1 | logger Jan 16 18:22:23 Tower kernel: xor: automatically using best checksumming function: pIII_sse Jan 16 18:22:23 Tower kernel: pIII_sse : 2671.200 MB/sec Jan 16 18:22:23 Tower kernel: xor: using function: pIII_sse (2671.200 MB/sec) Jan 16 18:22:23 Tower kernel: md: unRAID driver 0.95.4 installed Jan 16 18:22:23 Tower kernel: md: import disk0: [8,0] (sda) SAMSUNG HD204UI S2H7J1BZ912498 offset: 63 size: 1953514552 Jan 16 18:22:23 Tower kernel: md: import disk1: [8,16] (sdb) SAMSUNG HD204UI S2H7J1BZ912537 offset: 63 size: 1953514552 Jan 16 18:22:23 Tower emhttp: Spinning up all drives... Jan 16 18:22:23 Tower emhttp: shcmd (4): /usr/sbin/hdparm -S0 /dev/hda >/dev/null Jan 16 18:22:23 Tower kernel: md: import disk2: [8,48] (sdd) ST31500341AS 9VS1G56A offset: 63 size: 1465138552 Jan 16 18:22:23 Tower kernel: md: import disk3: [8,32] (sdc) ST31500341AS 9VS1F4RS offset: 63 size: 1465138552 Jan 16 18:22:23 Tower kernel: md: import disk4: [8,96] (sdg) ST31500341AS 9VS1JV6V offset: 63 size: 1465138552 Jan 16 18:22:23 Tower kernel: md: import disk5: [8,80] (sdf) ST31500341AS 9VS1G6RX offset: 63 size: 1465138552 Jan 16 18:22:23 Tower kernel: mdcmd (2): set md_num_stripes 1280 Jan 16 18:22:23 Tower kernel: mdcmd (3): set md_write_limit 768 Jan 16 18:22:23 Tower kernel: mdcmd (4): set md_sync_window 288 Jan 16 18:22:23 Tower kernel: mdcmd (5): set spinup_group 0 0 Jan 16 18:22:23 Tower kernel: mdcmd (6): set spinup_group 1 0 Jan 16 18:22:23 Tower kernel: mdcmd (7): set spinup_group 2 0 Jan 16 18:22:23 Tower kernel: mdcmd (: set spinup_group 3 0 Jan 16 18:22:23 Tower kernel: mdcmd (9): set spinup_group 4 0 Jan 16 18:22:23 Tower kernel: mdcmd (10): set spinup_group 5 0 Jan 16 18:22:23 Tower kernel: mdcmd (11): spinup 0 Jan 16 18:22:23 Tower kernel: mdcmd (12): spinup 1 Jan 16 18:22:23 Tower kernel: mdcmd (13): spinup 2 Jan 16 18:22:23 Tower kernel: mdcmd (14): spinup 3 Jan 16 18:22:23 Tower kernel: mdcmd (15): spinup 4 Jan 16 18:22:23 Tower kernel: mdcmd (16): spinup 5 Jan 16 18:22:24 Tower emhttp: shcmd (5): /usr/local/sbin/set_ncq sda 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (6): /usr/local/sbin/set_ncq sdb 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (7): /usr/local/sbin/set_ncq sdd 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (: /usr/local/sbin/set_ncq sdc 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (9): /usr/local/sbin/set_ncq sdg 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (10): /usr/local/sbin/set_ncq sdf 1 >/dev/null Jan 16 18:22:24 Tower emhttp: shcmd (11): /usr/local/sbin/set_ncq hda 1 >/dev/null Jan 16 18:22:24 Tower kernel: mdcmd (18): start STOPPED Jan 16 18:22:24 Tower kernel: unraid: allocating 33720K for 1280 stripes (6 disks) Jan 16 18:22:24 Tower kernel: md1: running, size: 1953514552 blocks Jan 16 18:22:24 Tower kernel: md2: running, size: 1465138552 blocks Jan 16 18:22:24 Tower kernel: md3: running, size: 1465138552 blocks Jan 16 18:22:24 Tower kernel: md4: running, size: 1465138552 blocks Jan 16 18:22:24 Tower kernel: md5: running, size: 1465138552 blocks Jan 16 18:22:24 Tower emhttp: shcmd (12): udevadm settle Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/disk3 Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/disk4 Jan 16 18:22:24 Tower kernel: mdcmd (20): check Jan 16 18:22:24 Tower kernel: md: recovery thread woken up ... Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/disk5 Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/cache Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/disk2 Jan 16 18:22:24 Tower emhttp: shcmd (13): mkdir /mnt/disk1 Jan 16 18:22:24 Tower kernel: md: recovery thread has nothing to resync Jan 16 18:22:24 Tower emhttp: shcmd (14): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/md5 /mnt/disk5 2>&1 | logger Jan 16 18:22:24 Tower emhttp: shcmd (15): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/md2 /mnt/disk2 2>&1 | logger Jan 16 18:22:24 Tower emhttp: shcmd (16): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/md4 /mnt/disk4 2>&1 | logger Jan 16 18:22:24 Tower emhttp: shcmd (17): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/hda1 /mnt/cache 2>&1 | logger Jan 16 18:22:24 Tower emhttp: shcmd (18): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/md3 /mnt/disk3 2>&1 | logger Jan 16 18:22:24 Tower emhttp: shcmd (19): set -o pipefail ; mount -t reiserfs -o noacl,nouser_xattr,noatime,nodiratime /dev/md1 /mnt/disk1 2>&1 | logger Jan 16 18:22:24 Tower kernel: REISERFS (device md5): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device md5): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device md2): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device md2): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device hda1): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device hda1): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device md4): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device md4): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device hda1): journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device hda1): checking transaction log (hda1) Jan 16 18:22:24 Tower kernel: REISERFS (device md1): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device md1): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device md5): journal params: device md5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device md5): checking transaction log (md5) Jan 16 18:22:24 Tower kernel: REISERFS (device md2): journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device md2): checking transaction log (md2) Jan 16 18:22:24 Tower kernel: REISERFS (device md3): found reiserfs format "3.6" with standard journal Jan 16 18:22:24 Tower kernel: REISERFS (device md3): using ordered data mode Jan 16 18:22:24 Tower kernel: REISERFS (device md4): journal params: device md4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device md4): checking transaction log (md4) Jan 16 18:22:24 Tower kernel: REISERFS (device hda1): Using r5 hash to sort names Jan 16 18:22:24 Tower kernel: REISERFS (device md1): journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device md1): checking transaction log (md1) Jan 16 18:22:24 Tower kernel: REISERFS (device md3): journal params: device md3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jan 16 18:22:24 Tower kernel: REISERFS (device md3): checking transaction log (md3) Jan 16 18:22:25 Tower emhttp: shcmd (20): cp /var/spool/cron/crontabs/root- /var/spool/cron/crontabs/root Jan 16 18:22:25 Tower emhttp: shcmd (21): echo '# Generated mover schedule:' >>/var/spool/cron/crontabs/root Jan 16 18:22:25 Tower emhttp: shcmd (22): echo '40 3 * * * /usr/local/sbin/mover 2>&1 | logger' >>/var/spool/cron/crontabs/root Jan 16 18:22:25 Tower emhttp: shcmd (23): crontab /var/spool/cron/crontabs/root Jan 16 18:22:25 Tower kernel: REISERFS (device md4): Using r5 hash to sort names Jan 16 18:22:25 Tower kernel: REISERFS (device md5): Using r5 hash to sort names Jan 16 18:22:25 Tower kernel: REISERFS (device md3): Using r5 hash to sort names Jan 16 18:22:25 Tower kernel: REISERFS (device md2): Using r5 hash to sort names Jan 16 18:22:25 Tower kernel: REISERFS (device md1): Using r5 hash to sort names Jan 16 18:22:25 Tower emhttp: shcmd (29): rm /etc/samba/smb-shares.conf >/dev/null 2>&1 Jan 16 18:22:25 Tower emhttp: _shcmd: shcmd (29): exit status: 1 Jan 16 18:22:25 Tower emhttp: shcmd (30): cp /etc/exports- /etc/exports Jan 16 18:22:25 Tower emhttp: shcmd (31): mkdir /mnt/user Jan 16 18:22:25 Tower emhttp: shcmd (32): /usr/local/sbin/shfs /mnt/user -cache 1 -floor 2000000 -o noatime,big_writes,allow_other,default_permissions Jan 16 18:22:26 Tower emhttp: shcmd (33): mkdir /mnt/user0 Jan 16 18:22:26 Tower emhttp: shcmd (34): /usr/local/sbin/shfs /mnt/user0 -cache 0 -o noatime,big_writes,allow_other,default_permissions Jan 16 18:22:27 Tower emhttp: shcmd (35): killall -HUP smbd Jan 16 18:22:27 Tower emhttp: shcmd (36): /etc/rc.d/rc.nfsd restart | logger Jan 16 18:24:39 Tower login[1341]: ROOT LOGIN on `tty1' Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 ifconfig: eth0 Link encap:Ethernet HWaddr 00:00:00:00:09:a9 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:129 errors:0 dropped:0 overruns:0 frame:0 TX packets:337 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16571 (16.1 KiB) TX bytes:58040 (56.6 KiB) Interrupt:18 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3168 (3.0 KiB) TX bytes:3168 (3.0 KiB) Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 reserved for more logfiles Quote Link to comment
leech Posted January 16, 2011 Author Share Posted January 16, 2011 reserved for more logfiles Quote Link to comment
RobJ Posted January 17, 2011 Share Posted January 17, 2011 It is always good to see users bravely attempting to make unapproved hardware work with unRAID, and I commend you for trying. In your case, the odds are really stacked against you though. 1. The board is VIA based, and unfortunately, while there have been a few that worked (here is one), I don't think most users have had much success. The few that did work often had various limitations and poor performance. 2. It is using a "Centaur VIA Eden Processor 1200MHz". That is a 1.2GHZ single core processor, and I don't recall anyone using one as slow as that. It does not mean it cannot work, but performance will be poor. It is also a non-standard processor, that I have absolutely no experience with, but it does not inspire confidence in its compatibility. I have been out of touch for awhile, so perhaps others have tested it. 3. You are running with only 446MB of RAM, somewhat less than our usual recommended minimum of 512MB. I suspect you have 512MB of RAM minus a 64MB portion reserved for onboard video, so check the BIOS settings and see if you can revise that to the minimum possible for video use. Even if you can adjust that to 8MB for video, giving you about 504MB for unRAID, you may have problems, because unRAID keeps growing, and there are so many good addons. If you do get your system working satisfactorily, you will still need to be VERY selective with any addons. Running out of memory is probably the number one way to crash unRAID. I recommend at least 1GB of RAM. You appear to have a Sil3114-based card on the PCI bus with 4 SATA drives. You also appear to have a Realtek gigabit network chipset on your PCI bus. That is going to be a serious bottleneck, with slower parity checks and builds, and possibly slower network access too during heavy disk I/O. The syslog attached in the first post (that is the preferred way to attach it) looks very good, but it is only a record of a fresh boot, before any problems have occurred, so there is nothing that can be said about the problems that you have had. Try to capture a syslog after you have had issues, and before rebooting. From your comments, it sounds like you may have run out of RAM (and processes would have been shut down), and/or there are compatibility issues with your network chipset and/or motherboard. This is just speculation though, without a syslog that captured the errors reported. Quote Link to comment
leech Posted January 17, 2011 Author Share Posted January 17, 2011 Thanks for your Reply. Sorry but i didn't have build that System on my own. I bought it from a Retailer since i didn't want to build it myself. http://www.bettershopping.eu/de_AT/shop/PC_Hardware/NAS-Systeme/NAS-Gehaeuse/ART00927_NAS_Gehaeuse_MAREL_GreenIT_unRAID_6x3_5_Tower.html?currency=EUR until the System broke it runs fine for weeks without speed issue or something.... I bought this system cause i wanted to avoid Hardware problems.... and now this Ahm... this Syslog copy i made minutes after the problem occur. But anyhow, when the hardware isn't good overall i think i'll rebuild it by myself. I got an old HTPC with a core2duo and 1gig of ram (or maybe 2, but it's upgradeable) i think its an elitegroup or ASrock mainborad or something. Have to look if it's on the supported hardware list. I already thinked of an Hardware Upgrade cause the current Hardware couldn't take more than 6 drives... Quote Link to comment
leech Posted January 18, 2011 Author Share Posted January 18, 2011 i got a asrock mainboard with a core2duo. http://www.asrock.com/mb/overview.asp?Model=G31M-S it's not on the supported list but there are asus mainboards with the same G31/ICH7 chipset. i'm not sure about the lan, but i'll put it together and plug on the flash drive and see if it's going to do it's work. what do you think? Quote Link to comment
leech Posted January 21, 2011 Author Share Posted January 21, 2011 Finally i changed the Hardware and it works again. This Mainboard is compatible: http://www.asrock.com/mb/overview.asp?Model=G31M-S How to add this to the Compatiblity list? Cause this Board got a Realtek 8103EL/8102 Network Interface and until now this isn't listed in the list. I know it's only 100mbit. buts it's on the board and does it'S job until i get another. Also Seagate ST31500341AS Seagate ST380815AS Samsung HD204UI Harddisks are working. Quote Link to comment
RobJ Posted January 21, 2011 Share Posted January 21, 2011 Great! Looks like the board should work fine. When I or someone else has a chance, we'll add that board to the Hardware Compatibility page. As you probably know though, it's not likely to be very popular with only 4 SATA ports and 10/100 networking. The network chipset is going to be your worst bottleneck, limiting all file transfer to and from your server to about 10MB/s speed. If you can find a cheap gigabit card, you will double or triple that speed. I too have been trying to get by with very cheap and used hardware. The one thing I could not live without though, is gigabit networking, 10MB/s is sooooo slow. But if you are going to be upgrading anyway, most modern motherboards come with built-in gigabit networking. Quote Link to comment
leech Posted January 23, 2011 Author Share Posted January 23, 2011 yeah it's slow, but better than nothing ^^ maybe i'll get a cheap gbit card but i think the currently setup will last for a while. I finally want to build a Pro Server with 20 drives, and therefore i need another mainboard anyhow... (or more expensive controller) Until then, HD movie streaming also works with 100mbit Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.