Issue with one computer on the network

Hi,

I'm not sure if this is an unRAID issue or an issue with my computer, but I'm hoping someone can point in the right direction if it's not unRAID.  I have 3 computers on the same network as the unRAID box.  Two of them and read and write just fine, but my computer cannot.  It can read (although the reads seem to be slower than on the other systems - around 14 MB/s), but if I try to write something, it waits around 30 seconds and just fails (I'll attach a screen shot of the error).  I think it may be something with my Windows 7 installation because if I boot into my Arch Linux installation on the same machine, I have no problems.  This issue just started a couple days ago.  Before that, I had no problems reading or writing with the win7 installation.  Anything to shed some light on what might be the issue would be greatly appreciated.  Thanks!

P.S. - unRAID is 5.0 beta 14, the other machines that have no problem accessing are both win7.

P.P.S - The first screenshot is what comes up when the transfer first starts, and the second is the error that I get after around 30 seconds.

Sounds like your computer to me, not unraid . What security software are you running ?

I use Microsoft Security Essentials.

How is this computer connected to the network cat cable or wifi? Try to give us as much information as possible. Did you already try to shutdown all computers and servers  on your network? Did you try to ping the machine having problems?

The computer is connected via gigabit Ethernet.  All the computers and the unRAID box have been restarted multiple times.  I can successfully ping this computer from the unRAID box.

I use Microsoft Security Essentials.

I had Micro. Security Essentials too, and I had to remove it.  My second media player was able to connect to my shares.  That's when I had my shares in my W7 PC.  I never installed it back again, and I've never had any issues after that.

Try turning it off and see if that does anything.  Have you tried turning on / off your router?  I had one occasion when power went out.  Everything turn back on after 5 min., but I wasn't able to access my server from any of my computers.  I've got IP's reserved for all my individual gadgets, and for some reason or another everything got erased from my router LAN.  I turned the router off / on and everything came back to normal.

Neither turning off Security Essentials nor restarting the router made any difference, unfortunately.

Network connectivity problems have various causes, but they typically occur because of incorrect network adapters, incorrect switch settings, faulty hardware, or driver issues. Some connectivity symptoms are intermittent and do not clearly point to any one of these causes.

Common causes of connectivity problems are as follows:

Network adapters and switch ports have mismatching duplex levels or transfer speed settings.

Network adapters or switches with transmission rates of 10/100 megabits per second (Mbps) do not switch over correctly. Some autosense settings may not correctly detect the speed of some network adapters.

The network adapter is incompatible with the motherboard or other hardware or software components and drivers.

Typical error messages include the following:

Error 55: "The specified network resource is no longer available" (ERROR_DEV_NOT_EXIST).

Error 64: "The specified network name is no longer available" (ERROR_NETNAME_DELETED).

Error 121: "The semaphore timeout period has expired" (ERROR_SEM_TIMEOUT).

Error 1231: "The remote network is not reachable by the transport" (ERROR_NETWORK_UNREACHABLE).

The system event logs of the client computer may show any one of the following entries:

Type: Warning

Source: MrxSmb

Event ID: 50

Description:

{Lost Delayed-Write-Data} The system was attempting to transfer file data from buffers to \Device\LanmanRedirector. The write operation failed, and only some of the data may have been written to the file.

Type: Warning

Source: MrxSmb

Event ID: 3013

Description:

The redirector has timed out to ServerName

Type: Warning

Source: MrxSmb

Event ID: 3036

Description:

The redirector detected a security signature mismatch. The connection has been disconnected.

There may be multiple occurrences of the following TCPIP 4201 entry in the event logs:

Type: Information

Source: TCPIP

Event ID: 4201

Description:

The system detected that network adapter Compaq NC6134 Gigabit NIC was connected to the network, and has initiated normal operation over the network adapter.

A single TCPIP 4201 event is typical after you restart the computer or after you disable or enable the network adapter.

Back to the top

Troubleshooting

To troubleshoot network adapter problems, follow these steps:

Use the Ping or PathPing command-line tools to test basic connectivity. Use Ping to isolate network hardware problems and incompatible configurations. Use PathPing to detect packet loss over multiple-hop trips.

To watch Ping statistics, use the ping -t command. To see statistics and continue, press CTRL+BREAK. To stop, press CTRL+C. If you detect lost packets in the statistics output, it indicates networking problems up to Open Systems Interconnection (OSI) layer 3 (IP-level connectivity).

If the remote system that you ping is across a high-delay link, such as a satellite link, responses may take longer. Use the -w (wait) switch to specify a longer time-out.

Check the event logs for network-card-related entries or connectivity-related entries.

For more information, click the following article number to view the article in the Microsoft Knowledge Base:

308427  How to view and manage event logs in Event Viewer in Windows XP

Check whether the network adapter is on the Microsoft Hardware Compatibility List (HCL). To see the HCL, visit the following Microsoft Web site:

http://winqual.microsoft.com/HCL/Default.aspx?m=x

Check other computers that use the same default gateway that are plugged into the same hub or switch. If these computers do not experience network connectivity problems, the problem may be a faulty network adapter on one computer.

If this is the case, update the network adapter driver to the latest version.

Contact the vendor of each motherboard and update the BIOS of the boards. Some network adapters and motherboards or BIOS versions are incompatible. Obtain the latest version from the vendor's Web site or contact your hardware vendor.

Check the network adapter and uplink hardware (hub or switch) for common settings. Make sure that all complementing network resources (network adapter, hub, and switch) are set to the same speed and duplex level. If the media type is set to autosense, autosensing, or autodetect, or "Auto Select," make sure that all components are autosensing correctly.

On some switches, a duplex setting of Auto may cause it to use half-duplex. You may have to force it to use full-duplex.

Reset the switch, restart the client, and test the connectivity.

Put the client and the server on a passive hub. If communication resumes, the problem may be caused by an incorrect network switch configuration.

For more information about how to configure the devices, contact your hardware vendor.

Manually set the network adapter of the computer that has connectivity problems to half-duplex and a lower speed.

Connect the system to a switch that is configured to half-duplex and 10-Mbps, or use a 10-Mbps hub, to see whether connection can be established at a lower transmission speed.

To increase performance, increase the speed settings manually to 100 Mbps, and then restart the computers. Test for network connectivity loss, increase the setting to full-duplex, and then restart the computers. If network loss occurs, reduce the duplex setting and the speed to the previous settings.

Swap the network cable between the failing system and the hub or switch.

Replace the network adapter with a network adapter that has been tested and proven reliable. To do this, follow these steps:

Remove the network adapter diagnostics program.

Remove the network adapter in Network properties.

Install the new network adapter.

Run Network Monitor at the same time on both ends of the network connection. After you filter the traces on the addresses of the two systems, compare both traces to see whether you can see the same traffic.

Use TCP Retransmit, the Network Monitor Experts tool, to detect TCP retransmissions. To do this, follow these steps:

Start Network Monitor.

On the Tools menu, click Experts, and then click TCP Retransmit in the navigation pane.

Click Add to Runlist.

Click Run Experts.

If frames are missing in one of the traces, check all intermediate cabling, hubs, switches, and routers for hardware or configuration errors.

In Network Monitor, view the Capture Statistics summary frame. This frame is the last frame of the trace. If it contains a value other than 0 in the following statistic counters, the connectivity problem may be caused by a hardware or configuration problem:

STATS: MAC CRC Errors = 0

STATS: MAC Frames Dropped due to HardWare Errors = 0

Network switches and server network adapters have to have the duplex settings matched for communication to function correctly. Both must be set to full-duplex or half-duplex. They cannot be mismatched.

The computers on a local area network (LAN) typically share a common full-duplex network medium. This configuration permits two computers to transmit data at the same time.

Connectivity problems may occur if either of the following conditions is true:

The computer was moved to a new Ethernet switch port that automatically senses network speed. However, the computer's network adapter is configured to force full-duplex communication with a static network transfer speed setting (10 Mbps, 100 Mbps, or 1 gigabit per second [Gbps]).

Both the Ethernet switch port and the computer's network adapter are configured to force 100-Mbps or 1-Gbps full-duplex communication. However, the Ethernet switch or the network adapter may not be able to communicate at that rate or may not be able to use full-duplex transmissions.

You can improve network performance in an Ethernet LAN environment by using full-duplex hardware. This configuration permits two-way communication between networked devices. Without full-duplex hardware, information is sent one way and then sent the other way. Packets frequently collide on the network in a half-duplex hardware configuration, and every time a collision occurs, the packets that collided must be resent. This creates even more traffic that can decrease network performance.

With full-duplex, transmit and receive paths are separate. Therefore, you can transmit and receive at the same time, and collisions are prevented. Because of the increased throughput and lack of collisions, full-duplex is more susceptible to bad cable terminations or to cable attenuation that exceeds recommended limits. This can generate data retransmissions that become sufficient to degrade performance.

Sorry for that long post.  That's what a friend of mine (IT dude) directed me to.

I also found this comment on Microsoft Support:

"This is caused by Symantec Endpoint Protection 11.0, Symantec has identified this as a known issue."

To resolve this issue, contact Symantec to assist you with the SymantecEndpointProtection software or Symantec Antivirus software.

For more information about how to obtain support for these products, visit: http://service1.symantec.com/SUPPORT/ent-security.nsf/docid/2007121216494948

Use one of the following methods:

Method 1: Update your copy of Symantec Endpoint Protection to the latest version available

Symantec has identified this as a known issue (bug) and they have published a an update to these programs to resolve this issue:

·        http://service1.symantec.com/SUPPORT/ent-security.nsf/docid/2007102613484948

Method 2:  Completely remove Symantec Endpoint Protection 11.0

Please follow Symantec documents or contact Symantec support to use this method. To contact Symantec visit one of the following Symantec Web sites:

http://service1.symantec.com/SUPPORT/ent-security.nsf/docid/2007101615023748

  http://service1.symantec.com/support/ent-security.nsf/854fa02b4f5013678825731a007d06af/5db8e519e16d42f2882573290005aa1d?OpenDocument

If I was you I would uninstall all security software. And restart the computer and try again ,you have to start eliminating software , hardware , ect .. to see what's stopping you from seeing those shares. Good luck Ryan