davejcb Posted September 26, 2012 Share Posted September 26, 2012 Good morning all, I'm running the latest 5.0-rc8a, with two 2TB WD Green data drives, 1 2TB WD Green parity drive, and one 500GB Maxtor cache drive. I noticed yesterday that my second data drive was unassigned, and in unMENU was showing as DISK_INVALID. Shut the server down, checked cables, rebooted, the disk was there, but had a yellow dot next to it. Tried rebuilding it, was taking forever (300kb/sec), cancelled it. At this point, my parity drive showed as unassigned! Rebooted, the drive is assigned but with a blue dot (new drive). I'm not sure where to go from here- I fear that I now have a lost second data drive with an invalid parity drive that I can't use to rebuild from. I have the option of starting the array and parity-syncing, but I fear what would happen if I did this. I'll be heading out today to pick up a new 2TB disk. I'm thinking of dd'ing the second data disk to this new drive as a backup in case the worst happens. So to recap, I currently have my second data drive with a yellow dot and my parity drive with a blue dot, array is not started. I welcome your advice. Dave Quote Link to comment
dgaschk Posted September 26, 2012 Share Posted September 26, 2012 Attach a syslog. Quote Link to comment
davejcb Posted September 26, 2012 Author Share Posted September 26, 2012 Apologies for missing that. Here it is... log.txt Quote Link to comment
davejcb Posted September 26, 2012 Author Share Posted September 26, 2012 Here's a screenshot of how things look... Quote Link to comment
dgaschk Posted September 27, 2012 Share Posted September 27, 2012 Attach a new syslog that shows more. Attach SMART reports. Quote Link to comment
davejcb Posted September 27, 2012 Author Share Posted September 27, 2012 Not a lot more to find in the log... log.txt Quote Link to comment
davejcb Posted September 27, 2012 Author Share Posted September 27, 2012 The SMART reports... sda.txt sdc.txt sdd.txt sde.txt Quote Link to comment
davejcb Posted September 27, 2012 Author Share Posted September 27, 2012 Little update- I've taken the 2nd data drive and connected it to an Ubuntu PC, and was able to mount it and see the contents, all of which seem to be intact. I have a brand new drive, not sure of the order of things I should take... The drive is currently unformatted. Should I: 1- leave the data drive disconnected, connect the new drive and pre-clear it, assign it to the array, then return the data drive and copy it over? 2- copy the data via dd after pre-clearing the new drive and assigning it to the array? Thanks for the advice! Quote Link to comment
davejcb Posted October 2, 2012 Author Share Posted October 2, 2012 OK, I need help here- I've copied over the data from my 2nd data drive to USB drive, data is safe. Both the 2nd data disk and the parity disk are yellow, and show as DISK_INVALID under unMENU. I've run SMART reports on the data drive it seems fine, only the filesystem is corrupt. I try and format the drive from the main menu, but nothing happens. If I pop in a fresh disk it says "Invalid expansion" and won't accept it. I can't format, can't add a disk, can't remove the parity drive, what CAN I do here??? Quote Link to comment
davejcb Posted October 2, 2012 Author Share Posted October 2, 2012 Log... log.txt log.txt Quote Link to comment
davejcb Posted October 3, 2012 Author Share Posted October 3, 2012 Any kind of help, please? I would truly appreciate suggestions. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.