erichner

Just jumping in here as I experienced all of my Shares disappearing as well about 10 minutes ago. No logs saved unfortunately.

Would something like this work? i like the idea of it coming with cables and supporting 24 drives when I upgrade in the future.

I wish I could do the 8i but I have 9 HDD drives. Also, my NVMe drive is mounted to board directly for a bare metal VM, so no worry there. I figure with the 9305-16i or 9400-16i I can get one or two dual SSD 2.5in drive to 3.5in HDD adapters and put in another one or two of my extra drives as well. Thanks for all the info!

I don't have any experience with SAS HBA boards, so please excuse my ignorance. Would any of these work that are closer to my budget of $200 or less: LSI SAS9750-16I4E 16 Port Internal 4 Port External 6Gb/s PCI SATA+SAS https://www.ebay.com/itm/LSI-SAS9750-16I4E-16-Port-Internal-4-Port-External-6Gb-s-PCI-SATA-SAS/372880810737?hash=item56d16da2f1%3Ag%3AsEsAAOSwbTVd-nha&LH_BO=1 LSI Megaraid SAS 9260-16I SAS 512MB Controller L3-25243-20D W/ BATTERY & CABLES https://www.ebay.com/itm/LSI-Megaraid-SAS-9260-16I-SAS-512MB-Controller-L3-25243-20D-W-BATTERY-CABLES/254427115539?hash=item3b3d09b013%3Ag%3AaIMAAOSwk5Fd1EMy&LH_BO=1 ----------------------- Would this one be better than the 9305-16i if I was going to spend $300: Broadcom LSI SAS 9400-16i (05-50008-00) 12Gb 16 Port HBA - New Sealed Box https://www.ebay.com/itm/Broadcom-LSI-SAS-9400-16i-05-50008-00-12Gb-16-Port-HBA-New-Sealed-Box/264370017310?hash=item3d8dae541e:g:z1UAAOSweOldAPB8

Is the 3rd server still around? I'm looking for my second to house my smaller drives....

The 1050 runs in PCIe 1x due to an converter / extension I used to mount the card upside down. Wasn't due to the actual motherboard.

Any suggestions on a LSI card that can do SATA/SAS and support 16 drives (up to 16tb) and won’t break the bank? Any idea of how much of a performance increase a 6GBps vs a 12GBps card would make? I have (9) 3.5in drives + (2) cache SSDs + (1) SSD for VM. Does it make sense to use the Marvell controller only for drives that are not in the array and for specific VMs? This would be for the use of unassigned drives will not be consistently pushed as they are now with seeding/uploading torrents in Qbittorrent (and causing the disk errors).

Running Qbittorrent causes massive file errors that normally knocks off 1 parity and 1 data drive offline. Rebuilds required to get back online. I've replaced the parity drive that I thought was in question and recently added a new one that is now suffering from these disk errors, regardless of the SATA port. I usually have these running simultaneously without error in the past: Plex Qbittorrent Radarr Radarr4k (same but for 4K) RadarrSync Sonar Jackett Lidarr Krusader Logs attached tower-diagnostics-20200320-0152.zip

Logs for 6.8.0rc7 tower-diagnostics-20191201-0250.zip

Everything has been running fine on 6.4.3 for 2+ years now. When I try and upgrade, the drives running off the external sata card disappear. I have removed all of the Dynamix plugins as previously suggested. Meant 6.8.0rc7 not rc8. Logs for 6.4.3 tower-diagnostics-20191130-2125.zip

I've actually disabled the debug mode for CA Auto Turbo as of yesterday, before the most recent crash. EDIT: I followed your link and updated the items suggested. We'll see if it is still showing more OOM errors today!

Issue: Whenever my Cache drive has less than 64GB of free space (total amount of ECC Ram I have), the system goes haywire. GUI is unresponsive. I get the following error since the /user folder disappears: Transport endpoint is not connected Mover is run every hour to keep the Cache drive as empty as possible. I have a share IncomingMedia that is set to use the Cache and have a MEGAdownloader program on my physical Mac mapped to the share as the download location. My process for getting media and transporting it to unRAID: 1) Select files to start auto downloading on the Mac 2) Files start to save on unRAID IncomingMedia share from Mac 3) After files have downloaded, I move them from a "Downloading" folder to a "Completed" folder (no moving actually happens from Cache, since both folders are under IncomingMedia) 4) I then do a move via Midnight Commander (MC) in terminal to my PlexMedia share (also set to use Cache) Diagnostics are attached. System: unRAID 6.3.5 Intel® Xeon® CPU E5-2650 v3 @ 2.30GHz 2 Cache drives (506GB useable) - 512GB 850 Pro - 500GB 850 Evo 1 Parity drive - 8TB WD Pro 7 Data drives - 2x 8TB WD Reds - 4x 3TB Seagate NAS - 1x 3TB Toshiba 3 Unassigned drives - 512GB SSD 850 Pro NVMe (used for VM) - 960GB SSD for (games for VM) - 32GB Flash drive for backups of unRAID USB unraid-diagnostics-20180104-1051.zip

Yes, you're right. I updated my post to reflect the correction. My homebridge has been running all day so far!

So for all of you that are having issues with the Homebridge docker quitting after X amount of time (most likely due to the harmonyhub plugin). Try this: Edit the docker Turn on Advanced In parameters add: --restart=unless-stopped This should restart the docker if it crashes unexpectedly.

I had to upgrade my unRAID setup to 6.3.3 a few months back after a USB drive died. I feel like an idiot, but how would I run your script in Windows 10? I am still trying to get this to work again.